PERMATEX INDUSTRIAL CORP -- 81160, 26BR, FORM-A-GASKET (R) SEALANT, HIGH (SUPDAT)  -- 8030-00N056056
<pre>=====================  Product Identification  =====================

Product ID:81160, 26BR, FORM-A-GASKET (R) SEALANT, HIGH (SUPDAT)
MSDS Date:05/26/1993
FSC:8030
NIIN:00N056056
=== Responsible Party ===
Company Name:PERMATEX INDUSTRIAL CORP
Address:705 N MOUNTAIN RD
City:NEWINGTON
State:CT
ZIP:06111
Country:US
Info Phone Num:203-278-1280
Emergency Phone Num:800-641-7376
Preparer's Name:STEPHEN REPETTO
CAGE:62377
=== Contractor Identification ===
Company Name:PERMATEX INDUSTRIAL
Address:HARTFORD SQUARE N 10 COLUMBUS BLVD
Box:City:HARTFORD
State:CT
ZIP:06106
Country:US
Phone:877-376-2839
CAGE:62377

=============  Composition/Information on Ingredients  =============

Ingred Name:DOW CORNING 200 FLUID; (DIMETHYL POLYSILOXANE (ME TERM))
CAS:63148-62-9
RTECS #:JJ6484500
Fraction by Wt: 80-85%
OSHA PEL:N/K 
ACGIH TLV:N/K 

Ingred Name:SILICON DIOXIDE; (SILICA, AMORPHOUS (FUMED)
CAS:112945-52-5
RTECS #:VV7310000
Fraction by Wt: 10-15%
OSHA PEL:6 MG/M3
ACGIH TLV:10 MG/M3

Ingred Name:SILANE, METHYLTRIACETOXY-; (METHYLTRIACETOXYSILANE)
CAS:4253-34-3
RTECS #:VV4500000
Fraction by Wt: 1-5%
OSHA PEL:N/K 
ACGIH TLV:N/K 

Ingred Name:IRON (III) OXIDE
CAS:1309-37-1
RTECS #:NO7400000
Fraction by Wt: 1-5%
OSHA PEL:10 MG/M3 (FE)
ACGIH TLV:5 MG/M3 (FE)

Ingred Name:VOLATILE ORGANIC COMPOUND: 4.8% (EPA METHOD 24)
RTECS #:9999999VO
OSHA PEL:N/K 
ACGIH TLV:N/K 

=====================  Hazards Identification  =====================

LD50 LC50 Mixture:LD50: (ORAL) 2060 MG/KG
Routes of Entry: Inhalation:YES  Skin:NO  Ingestion:NO
Reports of Carcinogenicity:NTP:NO    IARC:NO	OSHA:NO
Health Hazards Acute and Chronic:ACETIC ACID PRODUCED DURING CURE
    IRRITATES EYES, NOSE AND THROAT.
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:METHYLTRIACETOXYSILANE: EYE, SKIN
    AND PULMONARY DISORDERS.

=======================  First Aid Measures  =======================

First Aid:INGESTION: DO NOT INDUCE VOMITING. KEEP INDIVIDUAL CALM.
    OBTAIN MEDICAL ATTENTION. INHALATION: REMOVE TO FRESH AIR. TREAT
    SYMPTOMATICALLY. SKIN: WIPE OFF PASTE WITH PAPER TOWEL OR CLOTH.
    WASH EXPOSED  AREA WITH SOAP AND WATER. EYES: FLUSH AT LEAST 15
    MINUTES WITH WATER. OBTAIN MEDICAL ATTENTION.

=====================  Fire Fighting Measures  =====================

Flash Point Method:TCC
Flash Point:>200F,>93C
Extinguishing Media:CARBON DIOXIDE, FOAM, DRY CHEMICAL.
Fire Fighting Procedures:USE NIOSH/MSHA APPROVED SCBA AND FULL
    PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:NONE.

==================  Accidental Release Measures  ==================

Spill Release Procedures:WIPE OR SCRAPE UP SPILLED MATERIAL. MAINTAIN
    GOOD VENTILATION FOR LARGE SPILL. PLACE SCRAP MATERIAL IN A WELL
    VENTILATED PLACE AND ALLOW TO CURE TO RUBBER.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

======================	Handling and Storage  ======================

Handling and Storage Precautions:STORE IN A DRY AREA BELOW 90F TO
    PRESERVE SHELF LIFE. KEEP CONTAINER CLOSED WHEN NOT IN USE.
Other Precautions:AVOID BREATHING VAPOR. AVOID EYE OR SKIN CONTACT.

=============  Exposure Controls/Personal Protection  =============

Respiratory Protection:USE NIOSH/MSHA APPROVED RESPIRATOR APPROPRIATE
    FOR EXPOSURE OF CONCERN .
Ventilation:PROVIDE LOCAL VENTILATION FOR PROLONGED USE IN CONFINED
    AREA.
Protective Gloves:RUBBER OR PLASTIC GLOVES.
Eye Protection:ANSI APPRVD CHEM WORKER GOGGLES .
Other Protective Equipment:NONE SPECIFIED BY MANUFACTURER.
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
MFR'S TRADE NAME/PART #: TEMP, SILICONE.

==================  Physical/Chemical Properties  ==================

Vapor Pres:10 @ 80F
Spec Gravity:1.05
Solubility in Water:POLYMERIZED
Appearance and Odor:RED PASTE; SHARP, IRRITATING ODOR.

=================  Stability and Reactivity Data  =================

Stability Indicator/Materials to Avoid:YES
NONE SPECIFIED BY MANUFACTURER.
Stability Condition to Avoid:POLYMERIZED BY CONTACT WITH MOISTURE.
    ACETIC ACID LIBERATED.
Hazardous Decomposition Products:ACETIC ACID, FORMALDEHYDE, SILICA
    FUME.

====================  Disposal Considerations  ====================

Waste Disposal Methods:CURED RUBBER SCRAP CAN BE INCINERATED. FOLLOW
    FEDERAL, STATE AND LOCAL REGULATIONS.

 Disclaimer (provided with this information by the compiling agencies):
 This information is formulated for use by elements of the Department
 of Defense.  The United States of America in no manner whatsoever,
 expressly or implied, warrants this information to be accurate and
 disclaims all liability for its use.  Any person utilizing this
 document should seek competent professional advice to verify and
 assume responsibility for the suitability of this information to their
 particular situation.