PUBLIC "-//W3C//DTD HTML 4.0
Transitional//EN">

Material
Safety Data Sheet

SECTION 1 PRODUCT AND
COMPANY IDENTIFICATION

Havoline® ATF+4
Automatic Transmission Fluid

Product Use:
Transmission
Fluid

Product Number(s):
CPS222270

Company
Identification

Chevron Products
Company

a division of Chevron
U.S.A. Inc.

6001 Bollinger Canyon
Road

San Ramon, CA
94583

United States of
America

Transportation
Emergency Response

CHEMTREC: (800) 424-9300
or (703) 527-3887

Health
Emergency

Chevron Emergency
Information Center: Located in the USA. International collect calls accepted.
(800) 231-0623 or (510) 231-0623

Product
Information

email :
[email-masked]

Product Information:
800-LUBE-TEK

MSDS Requests:
800-414-6737

SECTION 2 COMPOSITION/
INFORMATION ON INGREDIENTS

COMPONENTS

CAS
NUMBER

AMOUNT

Highly refined
mineral oil (C15 - C50)

Mixture

80 - 100
%weight

SECTION 3 HAZARDS
IDENTIFICATION

IMMEDIATE HEALTH
EFFECTS

Eye: Not expected to cause prolonged
or significant eye irritation.

Skin: Contact with the skin is not
expected to cause prolonged or significant irritation. Contact with the skin is
not expected to cause an allergic skin response. Not expected to be harmful to
internal organs if absorbed through the skin. High-Pressure Equipment
Information: Accidental high-velocity injection under the skin of materials of
this type may result in serious injury. Seek medical attention at once should an
accident like this occur. The initial wound at the injection site may not appear
to be serious at first; but, if left untreated, could result in disfigurement or
amputation of the affected part.

Ingestion: Not expected to be harmful if
swallowed.

Inhalation: Not expected to be harmful if
inhaled. Contains a petroleum-based mineral oil. May cause respiratory
irritation or other pulmonary effects following prolonged or repeated inhalation
of oil mist at airborne levels above the recommended mineral oil mist exposure
limit. Symptoms of respiratory irritation may include coughing and difficulty
breathing.

SECTION 4 FIRST AID
MEASURES

Eye: No specific first aid measures
are required. As a precaution, remove contact lenses, if worn, and flush eyes
with water.

Skin: No specific first aid measures
are required. As a precaution, remove clothing and shoes if contaminated. To
remove the material from skin, use soap and water. Discard contaminated clothing
and shoes or thoroughly clean before reuse.

Ingestion: No specific first aid measures
are required. Do not induce vomiting. As a precaution, get medical
advice.

Inhalation: No specific first aid measures
are required. If exposed to excessive levels of material in the air, move the
exposed person to fresh air. Get medical attention if coughing or respiratory
discomfort occurs.

Note to
Physicians: In an
accident involving high-pressure equipment, this product may be injected under
the skin. Such an accident may result in a small, sometimes bloodless, puncture
wound. However, because of its driving force, material injected into a fingertip
can be deposited into the palm of the hand. Within 24 hours, there is usually a
great deal of swelling, discoloration, and intense throbbing pain. Immediate
treatment at a surgical emergency center is recommended.

SECTION 5 FIRE FIGHTING
MEASURES

Leaks/ruptures in high
pressure system using materials of this type can create a fire hazard when in
the vicinity of ignition sources (eg. open flame, pilot lights, sparks, or
electric arcs).

FIRE
CLASSIFICATION:

OSHA Classification (29
CFR 1910.1200): Not classified by OSHA as flammable or combustible.

NFPA RATINGS:
Health: 0
Flammability: 1 Reactivity: 0

FLAMMABLE
PROPERTIES:

Flashpoint:
(Cleveland Open
Cup) 190 °C (374 °F) (Min)

Autoignition: No Data Available

Flammability
(Explosive) Limits (% by volume in air): Lower: Not Applicable Upper: Not
Applicable

EXTINGUISHING
MEDIA: Use water
fog, foam, dry chemical or carbon dioxide (CO2) to extinguish flames.

PROTECTION OF FIRE
FIGHTERS:

Fire Fighting
Instructions:
This material will burn although it is not easily ignited. For fires involving
this material, do not enter any enclosed or confined fire space without proper
protective equipment, including self-contained breathing apparatus.

Combustion Products:
Highly dependent
on combustion conditions. A complex mixture of airborne solids, liquids, and
gases including carbon monoxide, carbon dioxide, and unidentified organic
compounds will be evolved when this material undergoes combustion.

SECTION 6 ACCIDENTAL
RELEASE MEASURES

Protective Measures:
Eliminate all
sources of ignition in vicinity of spilled material.

Spill Management:
Stop the source
of the release if you can do it without risk. Contain release to prevent further
contamination of soil, surface water or groundwater. Clean up spill as soon as
possible, observing precautions in Exposure Controls/Personal Protection. Use
appropriate techniques such as applying non-combustible absorbent materials or
pumping. Where feasible and appropriate, remove contaminated soil. Place
contaminated materials in disposable containers and dispose of in a manner
consistent with applicable regulations.

Reporting:
Report spills to
local authorities and/or the U.S. Coast Guard's National Response Center at
(800) 424-8802 as appropriate or required.

SECTION 7 HANDLING AND
STORAGE

Precautionary
Measures: DO NOT
USE IN HIGH PRESSURE SYSTEMS in the vicinity of flames, sparks and hot surfaces.
Use only in well ventilated areas. Keep container closed.

Keep out of the reach of
children.

General Handling
Information:
Avoid contaminating soil or releasing this material into sewage and drainage
systems and bodies of water.

Static Hazard:
Electrostatic
charge may accumulate and create a hazardous condition when handling this
material. To minimize this hazard, bonding and grounding may be necessary but
may not, by themselves, be sufficient. Review all operations which have the
potential of generating and accumulating an electrostatic charge and/or a
flammable atmosphere (including tank and container filling, splash filling, tank
cleaning, sampling, gauging, switch loading, filtering, mixing, agitation, and
vacuum truck operations) and use appropriate mitigating procedures. For more
information, refer to OSHA Standard 29 CFR 1910.106, 'Flammable and Combustible
Liquids', National Fire Protection Association (NFPA 77, 'Recommended Practice
on Static Electricity', and/or the American Petroleum Institute (API)
Recommended Practice 2003, 'Protection Against Ignitions Arising Out of Static,
Lightning, and Stray Currents'.

Container Warnings:
Container is not
designed to contain pressure. Do not use pressure to empty container or it may
rupture with explosive force. Empty containers retain product residue (solid,
liquid, and/or vapor) and can be dangerous. Do not pressurize, cut, weld, braze,
solder, drill, grind, or expose such containers to heat, flame, sparks, static
electricity, or other sources of ignition. They may explode and cause injury or
death. Empty containers should be completely drained, properly closed, and
promptly returned to a drum reconditioner or disposed of properly.

SECTION 8 EXPOSURE
CONTROLS/PERSONAL PROTECTION

GENERAL
CONSIDERATIONS:

Consider the potential
hazards of this material (see Section 3), applicable exposure limits, job
activities, and other substances in the work place when designing engineering
controls and selecting personal protective equipment. If engineering controls or
work practices are not adequate to prevent exposure to harmful levels of this
material, the personal protective equipment listed below is recommended. The
user should read and understand all instructions and limitations supplied with
the equipment since protection is usually provided for a limited time or under
certain circumstances.

ENGINEERING
CONTROLS:

Use in a well-ventilated
area.

PERSONAL PROTECTIVE
EQUIPMENT

Eye/Face
Protection: No
special eye protection is normally required. Where splashing is possible, wear
safety glasses with side shields as a good safety practice.

Skin
Protection: No
special protective clothing is normally required. Where splashing is possible,
select protective clothing depending on operations conducted, physical
requirements and other substances in the workplace. Suggested materials for
protective gloves include: 4H (PE/EVAL), Nitrile Rubber, Silver Shield, Viton.

Respiratory
Protection: No
respiratory protection is normally required.

If user operations
generate an oil mist, determine if airborne concentrations are below the
occupational exposure limit for mineral oil mist. If not, wear an approved
respirator that provides adequate protection from the measured concentrations of
this material. For air-purifying respirators use a particulate
cartridge.

Use a positive pressure
air-supplying respirator in circumstances where air-purifying respirators may
not provide adequate protection.

Occupational Exposure
Limits:

Component

Agency

TWA

STEL

Ceiling

Notation

Highly refined
mineral oil (C15 - C50)

ACGIH

5
mg/m3

10
mg/m3

--

--

Highly refined
mineral oil (C15 - C50)

OSHA
Z-1

5
mg/m3

--

--

--

SECTION 9 PHYSICAL AND
CHEMICAL PROPERTIES

Attention: the data below
are typical values and do not constitute a specification.

Color:
Red

Physical State:
Liquid

Odor: Petroleum odor

pH: Not Applicable

Vapor Pressure:
<0.01 @ 37.8
°C (100 °F)

Vapor Density (Air =
1): >1

Boiling Point:
>315°C
(599°F)

Solubility:
Insoluble

Freezing Point:
Not
Applicable

Density:
@ 15°C (59°F)

Viscosity:
7.5 cSt @ 100°C
(212°F) (Typical)

Evaporation Rate:
No Data
Available

SECTION 10 STABILITY AND
REACTIVITY

Chemical Stability:
This material is
considered stable under normal ambient and anticipated storage and handling
conditions of temperature and pressure.

Incompatibility With
Other Materials: May react with strong acids or
strong oxidizing agents, such as chlorates, nitrates, peroxides, etc.

Hazardous
Decomposition Products: None known (None
expected)

Hazardous
Polymerization: Hazardous polymerization will not
occur.

SECTION 11 TOXICOLOGICAL
INFORMATION

IMMEDIATE HEALTH
EFFECTS

Eye Irritation:
The eye
irritation hazard is based on evaluation of data for similar materials or
product components.

Skin Irritation:
The skin
irritation hazard is based on evaluation of data for similar materials or
product components.

Skin Sensitization:
The skin
sensitization hazard is based on evaluation of data for similar materials or
product components.

Acute Dermal Toxicity:
The acute dermal
toxicity hazard is based on evaluation of data for similar materials or product
components.

Acute Oral
Toxicity: The
acute oral toxicity hazard is based on evaluation of data for similar materials
or product components.

Acute Inhalation
Toxicity: The
acute inhalation toxicity hazard is based on evaluation of data for similar
materials or product components.

ADDITIONAL TOXICOLOGY
INFORMATION:

This product contains
petroleum base oils which may be refined by various processes including severe
solvent extraction, severe hydrocracking, or severe hydrotreating. None of the
oils requires a cancer warning under the OSHA Hazard Communication Standard (29
CFR 1910.1200). These oils have not been listed in the National Toxicology
Program (NTP) Annual Report nor have they been classified by the International
Agency for Research on Cancer (IARC) as; carcinogenic to humans (Group 1),
probably carcinogenic to humans (Group 2A), or possibly carcinogenic to humans
(Group 2B). These oils have not been classified by the American Conference of
Governmental Industrial Hygienists (ACGIH) as: confirmed human carcinogen (A1),
suspected human carcinogen (A2), or confirmed animal carcinogen with unknown
relevance to humans (A3).

SECTION 12 ECOLOGICAL
INFORMATION

ECOTOXICITY

This material is not
expected to be harmful to aquatic organisms.

ENVIRONMENTAL
FATE

Ready
Biodegradability:
This material is not expected to be readily biodegradable. The biodegradability
of this material is based on an evaluation of data for the components or a
similar material.

SECTION 13 DISPOSAL
CONSIDERATIONS

Use material for its
intended purpose or recycle if possible. Oil collection services are available
for used oil recycling or disposal. Place contaminated materials in containers
and dispose of in a manner consistent with applicable regulations. Contact your
sales representative or local environmental or health authorities for approved
disposal or recycling methods.

SECTION 14 TRANSPORT
INFORMATION

The description shown may
not apply to all shipping situations. Consult 49CFR, or appropriate Dangerous
Goods Regulations, for additional description requirements (e.g., technical
name) and mode-specific or quantity-specific shipping requirements.

DOT Shipping
Description: PETROLEUM LUBRICATING OIL, NOT
REGULATED AS A HAZARDOUS MATERIAL FOR TRANSPORTATION UNDER 49 CFR

Additional
Information:NOT
HAZARDOUS BY U.S. DOT. ADR/RID HAZARD CLASS NOT APPLICABLE.

IMO/IMDG Shipping
Description:
PETROLEUM LUBRICATING OIL; NOT REGULATED AS DANGEROUS GOODS FOR TRANSPORT UNDER
THE IMDG CODE (AMENDMENT 34-08)

ICAO/IATA Shipping
Description:
PETROLEUM LUBRICATING OIL; NOT REGULATED AS DANGEROUS GOODS FOR TRANSPORT UNDER
ICAO TI OR IATA DGR

SECTION 15 REGULATORY
INFORMATION

EPCRA
311/312 CATEGORIES: 1. Immediate (Acute) Health
Effects: NO

2. Delayed
(Chronic) Health Effects: NO

3. Fire
Hazard: NO

4. Sudden
Release of Pressure Hazard: NO

5.
Reactivity Hazard: NO

REGULATORY LISTS
SEARCHED:

01-1=IARC Group
1

03=EPCRA
313

01-2A=IARC Group
2A

04=CA Proposition
65

01-2B=IARC Group
2B

05=MA
RTK

02=NTP
Carcinogen

06=NJ
RTK

07=PA
RTK

No components of this
material were found on the regulatory lists above.

CHEMICAL INVENTORIES:

All components comply
with the following chemical inventory requirements: AICS (Australia), DSL
(Canada), IECSC (China), KECI (Korea), PICCS (Philippines), TSCA (United
States).

One or more components is
listed on ELINCS (European Union). Secondary notification by the importer may be
required.

One or more components
does not comply with the following chemical inventory requirements: ENCS
(Japan).

NEW JERSEY RTK
CLASSIFICATION:

Under the New Jersey
Right-to-Know Act L. 1983 Chapter 315 N.J.S.A. 34:5A-1 et. seq., the product is
to be identified as follows: PETROLEUM OIL (Automatic transmission
fluid)

WHMIS CLASSIFICATION:

This product is not
considered a controlled product according to the criteria of the Canadian
Controlled Products Regulations.

SECTION 16
OTHER INFORMATION

NFPA
RATINGS: Health:
0 Flammability: 1 Reactivity: 0

HMIS
RATINGS: Health:
1 Flammability: 1 Reactivity: 0

(0-Least, 1-Slight,
2-Moderate, 3-High, 4-Extreme, PPE:- Personal Protection Equipment Index
recommendation, *- Chronic Effect Indicator). These values are obtained using
the guidelines or published evaluations prepared by the National Fire Protection
Association (NFPA) or the National Paint and Coating Association (for HMIS
ratings).

LABEL
RECOMMENDATION:

Label Category :
INDUSTRIAL OIL 1 - IND1

REVISION
STATEMENT: This
revision updates the following sections of this Material Safety Data Sheet:
12,14,15,16

Revision
Date: August 13,
2009

ABBREVIATIONS THAT MAY HAVE
BEEN USED IN THIS DOCUMENT:

TLV
- Threshold Limit Value

TWA
- Time Weighted Average

STEL
- Short-term Exposure Limit

PEL
- Permissible Exposure Limit

CAS
- Chemical Abstract Service Number

ACGIH - American Conference
of Government Industrial Hygienists

IMO/IMDG - International
Maritime Dangerous Goods Code

API
- American Petroleum Institute

MSDS
- Material Safety Data Sheet

CVX
- Chevron

NFPA
- National Fire Protection Association (USA)

DOT
- Department of Transportation (USA)

NTP
- National Toxicology Program (USA)

IARC
- International Agency for Research on Cancer

OSHA
- Occupational Safety and Health
Administration

Prepared
according to the OSHA Hazard Communication Standard (29 CFR 1910.1200) and
the ANSI MSDS Standard (Z400.1) by the Chevron Energy Technology Company,
100 Chevron Way, Richmond, California
94802.

The above information is
based on the data of which we are aware and is believed to be correct as
of the date hereof. Since this information may be applied under conditions
beyond our control and with which we may be unfamiliar and since data made
available subsequent to the date hereof may suggest modifications of the
information, we do not assume any responsibility for the results of its
use. This information is furnished upon condition that the person
receiving it shall make his own determination of the suitability of the
material for his particular purpose.